EC Brush - new crankshaft deburring machine
13. October 2018
Before crankshafts are finished, careful deburring is a must. In most cases, this is done with the help of a robot that guides the workpieces to a tool console. The programming is extensive, the robot must be taught anew for each workpiece variant.
The EC Brush deburring machine from KADIA is an easy-to-use, cost-effective standard solution. It impresses with high productivity and low support and maintenance costs. The machine has five programmable axes and is flexibly designed so that it can process 3 to 6-cylinder crankshafts in any number of variants and alternately. An inclined bed construction makes the EC Brush an extremely compact machine with a space requirement of only 2.6 m x 2.3 m.
A brush with abrasive nylon fibers reliably removes loose particles, burrs and the like from the workpiece. The cross-section of the brush is adapted to the design of crankshafts. Long or short fibers are always in use, so that each main or connecting rod bearing is optimally reached. The main time for this process is about 20 sec. Including loading and unloading, cycle times of 30 sec are possible.
Various fiber types are available for process adaptation. Wet machining is also possible if the workpiece is to be rinsed. Of course, the EC Brush can also accommodate other comparable workpieces, such as camshafts. Click here for more information.
The following might also be of interest for you
Dually award-winning design
02. May 2021
The new E line single-spindle honing machine from KADIA has received not just one, but two prestigious awards: This year's iF Design Award, which it received in March, followed recently by the coveted "Red Dot" award.
With the generous access areas of its machining space framed in a darker tone, and its minimalist design that features clean, basic forms and smartly placed maintenance openings, the new E line single-spindle honing machine is consequently consistent with...MORE
Animated film on honing
07. May 2018
This is how kinematics and machining work during honing
Whenever there is a need to improve the functional sliding, guiding or sealing properties of contact surfaces in bores, all roads lead to honing.
In the case of high-precision parts, the achieved dimensional, geometrical and surface tolerances are less than 1 µm. But how exactly does this demanding process work? What are its characteristics?
What is typical to honing is, above all, the simultaneous overlaying of...MORE
V line – new flexible honing machine
02. May 2021
If the range of workpieces is large and quantities vary, a variable machining unit is needed. KADIA developed the V line for this constellation. The Vario honing machine is a flexible configurable honing solution with 2 or 3 honing stations.
The machine fits in line between the 2-spindle U line universal machine and the R line, which is equipped with up to 6 spindles, and it takes on their strengths: The structure is similar to the U line, very compact, with an integrated...MORE
RFID tool identification
11. March 2019
In keeping with the motto "Digitization increases process reliability", KADIA presented a field-proven Industry 4.0 application at the AMB exhibition in Stuttgart: A 2-spindle U line honing machine communicated with XM honing tools via a RFID tag. Important benefits are plausibility checks and the storage of information for later data analysis.
XM honing tools are equipped with read and writeable RFID data memories in which tool-specific identification and geometry data is...MORE
XC Honing Tools – Two-piece precision tools
02. May 2021
The XC honing tools from KADIA are based on a two-piece construction consisting of tool holder and tool body - C therefore stands for "Combined". A clamping unit allows both tool parts to be connected and disconnected in seconds. The XC tool system convinces with its high flexibility and high accuracy. The available diameters range from 4 mm to 40 mm.
The XC tools have been specially designed for the ultra-precise LH2 honing spindles with 17 mm clamping diameter. Like their...MORE
New Hybrid Deburr-Robot-Cell - high-pressure jet deburring included
02. May 2021
The mechanical processing of engine blocks leaves many burrs on surfaces, shoulders, bores or threads. Thorough deburring of all edges is therefore required for finishing and assembly. KADIA uses brush deburring for this task whenever possible.
However, with bores < 6 mm in diameter, the limit for brushing has been reached, so that another technology becomes necessary: high-pressure jet deburring. In a new Hybrid Deburr-Robot-Cell, KADIA now integrates both technologies...MORE
L LINE – NEW 2-SPINDLE HONING MACHINE DESIGNED FOR LONG COMPONENTS
02. May 2021
For the machining of very long bores with diameters < 20 mm, for a long time 3-spindle honing machines were the unsurpassed state of the art. Many KADIA customers all over the world have proven these machines. However, the common process sequence with rough, intermediate and finish honing requires a relatively complex machine concept with high space requirements at corresponding costs.
For KADIA this was one reason to develop a new compact high-performance machine for...MORE
NEW DEBURR-AUTOMATION-CELL FOR OPERATOR-FREE PRODUCTION
02. May 2021
Automation made by KADIA: The latest solution for combined deburring and handling of workpieces are multifunctional Deburr-Automation-Cells.
The centerpiece is a robot that performs not only the individual deburring operations, but also all the handling of the workpieces. Which means it loads and unloads a machining center and, if necessary, other connected production units, such as washing or quality stations. The possibilities are extremely diverse.
KADIA designs the...MORE
X line - new honing center for multiple bores
02. May 2021
KADIA already presented a prototype of the X line at EMO 2019 in Hanover (YouTube-Video). The feedback from visitors to the booth was incredibly positive, so much so that several orders were received in 2020 despite the pandemic.
The X line is a 2-spindle honing center in gantry design that combines flexibility and productivity. The machine's specialty is the sequential machining of several bores on one workpiece carrier.
Inside the X line, two LH3 honing spindles and...MORE
Stand-alone Plunge Measuring Station for Match Honing
20. October 2021
Match honing, the ultimate challenge in honing, is used whenever an exact match between piston and bore is required. First, the plunger is measured pneumatically, then the target diameter of the bore-to-be-honed is calculated individually. The basis for this is a defined match clearance of usually only a few µm. Normally, measurements and plunger handling are carried out fully automatically in a robot loading cell. If complex automation does not pay off, for example in the...MORE
Honing of BEV pinion gears with sophisticated design
09. April 2022
Honing of transmission gears has been one of KADIA's core competencies for many years. A honed bore with high dimensional accuracy and optimum surface finish reduces friction and promotes powertrain efficiency. This is particularly true for battery electric vehicles (BEV). System-related high standards of smooth operation are also required here.
Many of the BEV transmissions, some of which are very compact, contain stepped pinion gears with a sophisticated design. For...MORE